Guide / 6 min read

GTA VI Best Settings: What to Change on PS5 and Xbox Before You Play

The best GTA VI settings on PS5 and Xbox Series X and S: display, camera, aiming and console options that actually help at 30 fps, and the ones that do nothing.

Quick answer

The best GTA VI settings on PS5 and Xbox Series X and S: display, camera, aiming and console options that actually help at 30 fps, and the ones that do nothing.

Free Roam FYI Editorial · Updated

The short answer

- GTA VI runs at 30 frames per second on every console at launch, and there is no performance mode or graphics-mode toggle in the game. Our performance-mode guide explains why: https://freeroam.fyi/guides/gta-vi-performance-mode-60-fps-ps5-xbox - That does not mean the settings menu is useless. Ten minutes in Settings, plus two changes on your console and TV, makes Leonida sharper, steadier and easier to control. - Do the console and TV changes first, then the in-game Display, Camera and Controls tabs. The recommendations below come from launch-day guides that used the actual menus, and they are marked where the guides disagree.

Start with your console and TV

- Turn on Game Mode (ALLM) on your TV and switch motion smoothing off. Motion smoothing invents frames and makes a 30 fps game feel laggy; Game Mode cuts input delay. - Turn on VRR. On PS5: Settings, then Screen and Video, then Video Output, then VRR. On Xbox: Settings, then General, then TV and display options, then Video modes, then Allow variable refresh rate. VRR lets the TV match the console's actual output, which smooths the dips below 30 fps in heavy destruction scenes. - Enable 120 Hz output on the same menus. It does not unlock 60 fps — nothing does — but it helps the console and TV stay in sync. - Calibrate HDR on the console before you touch the in-game brightness screen. On PS5: Settings, then Screen and Video, then Video Output, then Adjust HDR. On Xbox: TV and display options, then Calibrate HDR for games. Run it in the lighting you actually play in, and turn on HGIG on your TV if it has the option, so the TV does not add its own tone mapping on top of the console's.

The HDR disagreement

- The guides split on HDR itself. Beebom's performance preset turns HDR off, and UNILAD's advice (via Geekblog) is to leave it off unless you have an OLED or another TV with high peak brightness, because on dim "HDR compatible" TVs it can look worse than standard dynamic range. - Wilson and MetaForge recommend HDR on, then calibrated. Our take: if your TV is an OLED or a bright LED, turn HDR on and calibrate it. If it is a budget TV that only claims HDR compatibility, try it off first and compare the opening drive in daylight.

Display settings in the game

- Motion Blur Strength: the default is 3. Beebom and Wilson both recommend 1, and MetaForge recommends 0 for the sharpest image at 30 fps. Start at 1; drop to 0 if fast driving still smears. - Player Status Effects, Hit Effects and Awareness Effects Intensity: all default to 5. Beebom sets them to 3 and Wilson to 2-3. Lower values thin out the screen effects that pile up in gunfights without changing what you can see. - Resolution: leave it on Native, or 1440p if you want a steadier image. On PS5 Pro, leave Enhanced PSSR Image Quality on Automatic. - Brightness Reduction and High Contrast Shaders: Beebom's performance preset leaves both off and its visual preset turns both on. These are accessibility options, so set them by comfort, not by frame rate.

Camera settings

- Cinematic Kill Shot Frequency: the default is 3. Wilson recommends 0-1, so the camera stops seizing control for kill cinematics in the middle of a fight. - Vehicle Crash Frequency: the default is 3. Wilson recommends 0 for the same reason — a crash cutscene is the last thing you want while you are trying to escape. - Camera Shake: on by default. MetaForge recommends turning it off if chases are hard to follow.

Controls and aiming

- Targeting: the default is Partial, which gently pulls your aim toward a nearby target. MetaForge recommends Lock-On for relaxed story play and Free Aim if you want a challenge. Aim Assist Strength defaults to 4 on a 0-5 scale; leave it at 4, or 0 if you switch to Free Aim. - Stick dead zones: the default is 4. Wilson recommends 2-3, which makes small stick movements register sooner. If your aim drifts when your thumbs are still, your sticks are worn or the dead zone is too low — raise it back a step. - Look and Aim Sensitivity: defaults are 6-7. Wilson recommends raising each by 1-2 steps if aiming feels sluggish. - Default Movement Speed: the default is Walk. Wilson recommends Jog, the fastest option, so you stop tapping to hurry everywhere. - Control Scheme: the default layout works, but MetaForge notes the Classic scheme matches GTA V's buttons if that is what your muscle memory expects.

HUD, audio and subtitles

- Subtitles: the default is Mission Only. MetaForge recommends On, so you catch radio, phone calls and street chatter that carry mission hints. - Navigation: the game asks you to pick a Navigation Experience on first launch. MetaForge recommends Always On while you are still learning the map, and Wilson recommends keeping the minimap always visible rather than dynamic. - 3D Audio: turn it on in the console settings if you play with headphones — PS5's Tempest 3D audio is one of the few console features Rockstar and Sony both highlight for this game.

What to ignore

- The PS5 system-level "Performance Mode" preset does nothing here. Wilson's guide calls this out directly: most pre-launch settings articles tell you to flip a preset that has no effect on GTA VI, because the game targets 30 fps regardless. - There is no in-game graphics mode toggle to find, on any console. If a guide tells you to switch to Performance Mode inside GTA VI, it was written before launch.

If the game still feels off

- Check Game Mode is on for the exact HDMI input your console uses — TVs remember it per input, and it is the most common reason the game feels laggy after a settings pass. - If aiming drifts, raise the dead zone back toward 4 instead of lowering sensitivity. - If the picture looks washed out, re-run HDR calibration in your actual play lighting before changing in-game brightness. - On Xbox Series S, no setting fixes the resolution: Digital Foundry measured 720p internal upscaled to 1080p with FSR, with thinner crowds and reduced texture detail. Our Series S guide has the full picture: https://freeroam.fyi/issues/gta-vi-xbox-series-s-performance-resolution-fps